:  Jun 18, 2007



. :
  All of the clips on the harness can be access with the integrated body installed to the frame. The graphic is to give guidance of the routing of the harness.

The frame wiring harness routing.



. Open the upper liftgate and lower tailgate.

. Remove the spare wheel and tire.

.
  : Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.

Raise and support the vehicle.

. Remove the wheels and tires.

. Disconnect the battery ground cable.

. Remove the LH front wheel arch liner.

. Remove the windshield washer reservoir filler neck.



. LH side behind the front headlamp: Disconnect the frame wiring harness electrical connector.



. LH side behind the front panel: Disconnect the 2 electrical connectors from the frame wiring harness.

. LH side behind headlamp: Release the 2 clips from the inner fender.



. LH side behind headlamp: Reposition the frame wiring harness down to the inner fender.

. LH side front: Release the 2 windshield washer jet hoses.



. Remove the frame wiring harness carrier.
  Remove and discard the 4 tie straps.
  Release the 2 clips.




. LH side front: Disconnect the height sensor electrical connector.



. Disconnect the ground cable from the wheel arch earth stud.
  Release the 2 clips.




. LH front side: Release the frame wiring harness from the frame.
  Release the 5 clips.




. Remove the air suspension reservoir.

. LH side: Release air suspension line from the frame wiring harness.
  Release the 4 clips.




. LH side: Release the frame wiring harness from the frame.
  Release the 6 clips.




. Remove the air suspension silencer.

. Remove the evaporative emission canister.

. Disconnect the 2 electrical connectors from the air suspension solenoid.



. Release the air suspension compressor valve block.
  Release the 3 grommets.




. LH side: Release air suspension line from the frame wiring harness.



.
  : Use a wrench on the hexagon provided to prevent the ball joint rotating.

Release both stabilizer bar links.
  Remove the 2 nuts.




. Release the stabilizer bar.
  Remove the 4 bolts.




. Release the frame wiring harness from the parking brake cable.



. Vehicles with differential locking motor: Disconnect the 2 electrical connectors.
  Release the 2 wiring harness clips.




. Release the parking brake emergency release cable.
  Release the 2 clips.




. LH side: Release the frame wiring harness.
  Remove the bolt.




. Disconnect the electrical connector from the rear LH height sensor.
  Release the 2 clips.




. LH side rear: Disconnect the air suspension rear valve block electrical connector.
  Release the clip.




. Release the valve block from its mounting bracket.
  Release the 3 grommets.




. Reposition the frame wiring harness to above the frame.

. LH side rear: Disconnect the 2 electrical connectors from the frame wiring harness.
  Release the 2 electrical connectors.




. Disconnect the LH rear ABS sensor.
  Release the clip.




. Release the parking brake actuator mount bracket.



. Spare wheel aperture: Release the frame wiring harness.
  Release the 5 clips.




. RH side rear: Disconnect the ABS sensor electrical connector.
  Release the 2 clips.




. RH side rear: Disconnect the low brake pad warning lamp electrical connector.
  Release the 2 clips.




. Disconnect the electronic parking brake actuator electrical connector.
  Release the clip.




. Release the RH parking brake cable.
  Remove the bolt.
  Release the clip.




. Release the fuel line support bracket.
  Remove the inner section of the fuel line support bracket.
  Release the clip.




. Release the frame wiring harness from the parking brake cable.



. RH side: Release the frame wiring harness from the frame.

. Remove the transmission under shield.
  Remove the 6 bolts.




. Remove the fuel tank heat shield.
  Remove the 3 bolts and 2 nuts.




. Release the parking brake emergency release cable.
  Release the 4 clips




.
  : Secure the component to the transmission jack.

  : Note the rear bolt is fitted with 2 washers.

Using a transmission jack, lower the fuel tank.
  Remove the 6 bolts.




. Disconnect the fuel pump module electrical connector.



. Release the frame wiring harness from the fuel tank.



. Rear of fuel tank: Release the frame wiring harness from the top of the frame crossmember.
  Release the clip.




. Secure the fuel tank.

. Release the exhaust heat shield for access.



. Release the brake pipes.



. With assistance, remove the frame wiring harness.
  Position both ends of the frame wiring harness to the LH center body mount.
  Route the front end of the frame wiring harness between the body and center crossmember.
  With assistance, remove the frame wiring harness.




. Check the old frame wiring harness against the new frame wiring harness to make sure that they are the same.

. :
  Make sure the wiring harness is routed correctly.

With assistance, install the frame wiring harness.
  Route all of the frame wiring harness electrical connectors and clips into position.

. Secure the brake pipes.

. Secure the exhaust heat shield.

.
  : Secure the component to the transmission jack.

  : Note the rear bolt is fitted with 2 washers.

Using a transmission jack, lower the fuel tank.
  Remove the 4 bolts.

. Connect the fuel pump module electrical connector.

. RH side: Secure the frame wiring harness to the fuel tank.

. Rear of fuel tank: Secure the frame wiring harness to the top of the frame crossmember.

.
  : Note the rear bolt is fitted with 2 washers.

Install the fuel tank.
  Tighten the bolts to 45 Nm (33 lb.ft).

. Secure the parking brake emergency release cable.
  Secure in the 4 clips.

. Install the fuel tank heat shield.
  Tighten the bolts to 6 Nm (4 lb.ft).
  Tighten the nuts to 3 Nm (2 lb.ft).

. Install the transmission under shield.
  Tighten the bolts to 10 Nm (7 lb.ft).

. RH side: Secure the frame wiring harness to the frame.

. Secure the frame wiring harness to the RH parking brake cable.

. Secure the RH parking brake cable bracket.
  Install the inner section of the parking brake cable bracket.

. Secure the RH parking brake cable.
  Secure the clip.
  Tighten the new bolts to 22 Nm (16 lb.ft).

. Connect the electronic parking brake actuator electrical connector.
  Secure the clip.

. RH side rear: Connect the low brake pad warning lamp electrical connector.
  Secure the 2 clips.

. RH side rear: Connect the ABS sensor electrical connector.
  Secure the 2 clips.

. Spare wheel aperture: Secure the frame wiring harness.
  Secure the 5 clips.

. Secure the parking brake actuator mount bracket.
  Tighten the bolts to 22 Nm (16 lb.ft).

. Connect the LH rear ABS sensor.
  Secure the clip.

. LH side rear: Connect the 2 electrical connectors to the frame wiring harness.
  Secure the electrical connectors.

. Reposition the rear valve block electrical connector.

. Reposition the RH side rear height sensor electrical connector.

. LH side rear: Connect the air suspension valve block electrical connector.
  Secure the clip.

. Connect the electrical connector to the rear LH height sensor.
  Secure the clip.

. Secure the valve block to its mounting.

. LH side: Secure the frame wiring harness.
  Tighten the bolt to 22 Nm (16 lb.ft).

. Secure the parking brake emergency release cable.
  Secure the clips.

. Secure the frame wiring harness to the LH parking brake cable.

. Attach both stabilizer bar links.
  Tighten the nuts to 115 Nm (85 lb.ft).

. Secure the stabilizer bar.
  Tighten the bolts to 62 Nm (46 lb.ft).

. Install the rear wheels and tires.

. Secure the air suspension compressor valve block.

. Connect the electrical connectors to the air suspension solenoid.

. Install the air suspension silencer.

. LH side: Secure the air suspension line to the frame wiring harness.

. LH side: Secure the frame wiring harness to the frame.
  Secure the 6 clips.

. Install the air suspension reservoir.

. Connect the ground cable to the wheel arch earth stud.
  Tighten the nut to 25 Nm (18 lb.ft).
  Secure the 2 clips.

. LH side front: Connect the height sensor electrical connector.

. Install the frame wiring harness carrier.
  Install new tie straps.
  Secure to the clips.

. LH side front: Secure the 2 windshield washer jet hoses.

. Reposition the frame wiring harness through the inner fender.

. LH side behind headlamp: Secure the 2 clips to the inner wing.

. LH side behind the front panel: Connect the 2 electrical connectors to the frame wiring harness.

. LH side behind the front headlamp: Connect the frame wiring harness electrical connector.

. Install the windshield washer reservoir filler neck.

. Install the LH front wheel arch liner.

. Connect the battery ground cable.